Whirlpool WTW5000DW1 Diagnostic Codes [Indications + Easy Fixes!]

No wonder the Whirlpool WTW5000DW1 washer is a promising model for its reliability and efficiency. But you know, to address potential issues and to fix the problem accordingly, this home appliance has diagnostic codes.

Whether you are a tech-savvy Whirlpool owner or an experienced technician, our guide on Whirlpool WTW5000DW1 diagnostic codes will provide you with complete insight to address the issue behind the error messages.

So, to get your Whirlpool laundry back on track, get going reading today’s write-up.

Whirlpool Washer WTW5000DW1 Diagnostic Codes: All Codes Fixed!

In both cases, where you are experiencing any error message on your Whirlpool WTW5000DW1 washer or just want to be prepared for future issues, having complete knowledge about the diagnostic codes is essential.

So, check out the Whirlpool WTW5000DW1 diagnostic codes with their indications and easy ways to fix them.

1. Error Code: F0E0

Error Indication– No error

2. Error Code: F0E2

Error Indication– The error code is displayed when the pressure sensor detects the suds level rising or the suds prevent the basket from spinning up to the speed.

How To Fix–

To resolve the problem, the main control will typically flush water attempting to clear the Whirlpool suds. If flushing can’t work out, check out the below things.

• First, ensure you’re using HE detergent. 
• Secondly, check whether you have used excessive detergent or whether there is any mechanical friction between the basket or drive mechanism. If yes, resolve it. 
• Thirdly, inspect for the kinked, or pinched pressure hose connection from the washer tub to the pressure sensor.

3. Error Code: F0E4

Error Indication– Whirlpool WTW5000DW1 washer detects the water temperature rising to 105° or higher during the rinse cycle.

How To Fix-

• Check whether the hot water is getting in the washer. 
• Ensure the inlet hoses are connected properly. If yes, then probably the temperature thermostat is stuck in the low resistance range. Check the resistance of it. 
• If the resistance is within the range shown in the table, replace the calibrated washer and main control. In case the resistance is close to zero or infinite, replace the thermostat assembly.

THERMISTOR RESISTANCE

Approx. Temperature		Approx. Temperature
F°	C°	(KΩ)
32	0	163
41	5	127
50	10	100
59	15	79
68	20	62
77	25	50
86	30	40
95	35	33
104	40	27
113	45	22
122	50	18
131	55	15
140	60	12
149	65	10

4. Error Code: F0E5

Error Indication– When the washer detects any off-balance condition, the code is displayed. 

How To Fix-

• Distribute the clothing in the washer evenly. 
• Inspect for weak suspension. You have to ensure that the basket doesn’t bounce up and down more than once when pushed.

5. Error Code: F1E1

Error Indication– Indicates that the main control is faulty.

How To Fix-

To resolve the error code F1E1, here you may need to check the main control and replace it when needed. It’ll be better to get the technician’s help.

6. Error Code: F1E2

Error Indication– Indication of the faulty motor control section in the main control.

How To Fix-

• Unplug the washer, and remove the console to access the main control. 
• Check the continuity of the motor control with an ohm meter. If the motor unit is faulty, replace it.

7. Error Code: F2E1

Error Indication– One or more key of the washer user interface is actuated for more than 15 seconds.

How To Fix-

If the status LED is flashing with 0.5-second intervals, what you need to do is-

• Step 1: Inspect the switch connector, and the harness between the switch and main control for any shorts. 
• Step 2: Replace the switch if there are any shorts.

8. Error Code: F2E3

Error Indication– The switches are not operating correctly or they don’t match the console.

How To Fix-

Here also, you need to check the switches of the Whirlpool wtw5000dw1 washer. If any of them is faulty, you need to replace the faulty one to resolve the problem.

9. Error Code: F3E1

Error Indication– Indicates that the pressure signal is out of range.

How To Fix-

• Check the pressure hose connection of your washer for pinched, plugged, or kinked ones. If there is a leak in the hose, replace it. 
• Moreover, if the hose is okay, check whether there is any debris. Run clear water to clean it out.

10. Error Code: F3E2

Error Indication– Open, shorted, or faulty inlet water temperature thermistor.

How To Fix– 

• Check the resistance of the temperature thermistor with the ohm meter. 
• If the resistance is within the recommended range, replace the main control. 
• If the resistance is zero or infinite, replace the temperature thermistor assembly.

11. Error Code: F5E1

Error Indication– Indicates Lid Switch issue. 

How To Fix- 

• First, check whether you’re pressing the Start button with the lid open. 
• Check if the Lid lock bezel is installed properly. 
• Inspect the lid switch assembly for any binding or obstruction. If necessary, replace it. 
• If not solved the issue, check the resistance of the lid switch. When the resistance is not within the range, replace the lid switch. If the lid switch is okay, then you may need to replace the main control. 

12. Error Code: F5E2

Error Indication– The error code indicates a faulty lid lock.

How To Fix- 

• Firstly, ensure the lid is closed properly. Inspect whether there is any lock interference. 
• Secondly, check whether wash media like lint, detergent, etc. buildup is preventing the sliding of the lock mechanism. 
• Thirdly, check the lid switch for any faults. If necessary, replace it.

13. Error Code: F5E3

Error Indication of F5E3 Code– The lid lock is not in an unlocked position or it can’t power the motor.

How To Fix-

• Step 1– Inspect whether there is any lock interference. 
• Step 2– Check for the faulty lid switch. Replace it if needed.

14. Error Code: F5E4

Error Indication– When you don’t open the lid after several consecutive washer cycles, and press the Start button, the code displays.

How To Fix- 

• Ensure that the error indication is resolved. 
• Lastly, inspect for the faulty lid switch.

15. Error Code: F7E1

Error Indication– Indicates that the main control isn’t able to detect the basket speed or the speed is changing too quickly.

How To Fix- 

• Ensure that the basket, motor, or impeller runs freely. 
• Inspect for faulty harness connection. 
• Check for broken wires to the motor. Moreover, check for a bad motor capacitor, and its connection, or loose drive belt or pulley.

16. Error Code: F7E5

Error Indication– Faulty shifter 

How To Fix- 

• Inspect the harness connection between the main control, motor, and shifter. 
• Observe the shifter function. Repair or replace accordingly.

17. Error Code: F7E6

Error Indication– Faulty motor

How To Fix-

To fix the issue, the motor needs to be checked thoroughly. That’s why it is better to call for the technician’s help.

18. Error Code: F8E1

Error Indication– The water level isn’t changed for a long period or the main control can’t detect the water level change.

How To Fix-

• Ensure adequate water supply to the washer. Check whether there is low water pressure due to clogged hose screens. 
• Check for proper hose installation. 
• Check for a fault-free hose connection between the tub and the pressure sensor.

19. Error Code: F8E3

Error Indication– The washer water level has exceeded the water capacity.

How To Fix- 

• Check the water level of the washer. 
• Inspect for the kinked or pinched hose connection. Ensure proper hose installation. 
• Check whether the pressure transducer is faulty.

20. Error Code: F8E5

Error Indication– Indicating reversed cold and hot hoses.

How To Fix-

First, ensure that the inlet hoses are connected properly, Secondly, inspect for the temperature thermistor,

21. Error Code: F9E1

Error Indication– When the water level doesn’t change even after the drain pump is opened for 10 minutes.

How To Fix-

• Check the drain hose or pump for obstruction. 
• If the hose pump is faulty, replace it. 
• Never use too much detergent.

FAQs

After going through all the Whirlpool wtw5000dw1 diagnostic codes, let’s check out some of the queries that the users mostly asked for better knowledge. 

Final Words

At last, as you see, understanding the Whirlpool wtw5000dw1 diagnostic codes is a must for homeowners for maintenance and efficient troubleshooting.

Through the guide, you can promptly diagnose the problem and can save money on simple repairs. If you’re still not so sure what to do, better to take the Whirlpool expert’s help.