Whirlpool Washer Stuck on Rinse [6 Possible Causes & Fixes]

Whirlpool washer users are claiming to be satisfied with the overall performance of their owned models. But we have seen some people objecting to an issue, which is that their washer sometimes gets stuck during a rinse. But why does it happen?

Technical glitches and overloaded clothes are the two common reasons why the Whirlpool washer stuck on rinse. Besides, timer defects, faults on the inlet valve, and faulty lid switch can cause the same bummer!

We guess you are not the only one searching for the troubleshooting of the above problems. That is what we will discuss in today’s write-up.

Troubleshooting and Fix for Whirlpool Washer Stuck on Rinse

The Whirlpool washer is prone to continue rinsing or spinning pretty normally. That said, just like other washers, it also has some limitations, restrictions, and drawbacks.

Like, it can start malfunctioning or cause issues with getting stuck during a rinse.

That is why we are going to highlight the common reasons why your Whirlpool washer stuck on rinse.

Including that, we will share the best and quickest way to troubleshoot each issue temporarily or completely –

1. Technical Glitches (Restart/Reset the Washer)

Sometimes, your Whirlpool washer can end up with technical glitches that are not in your hands. This often causes issues with getting stuck on a rinse cycle. In fact, it is considered one of the core causes behind the consequence.

Whether the stuck-related problem is occurring on rinse or wash cycle, the best and quickest way to fix it is to reset the system. To do so, press and hold the “Start” button for around three seconds.

Afterward, the washer will take a reset, and the issue will be gone if that happens due to a technical glitch.

2. Overload (Reduce the Load/Weight)

Uneven load is considered another common reason why your Whirlpool washer is stuck on rinse. Note that each washer consists of a specific load capacity, plus, you need to put the clothes as evenly as possible inside the washer.

In some cases, it is safe to get ideas about it through online or the owner’s manual to get familiar with the maximum load capacity. For instance, if your Whirlpool washer has a limit of up to 8 lbs, do not cross the range. And make sure to reduce slight loads if needed. 

3. Faulty Water Inlet Valve (Inspect It & Replace the Valve)

The prime function of a water inlet valve on a washer is to allow water into the washing machine during the wash cycle. So in case it is not functioning in the way it should be, chances are the washer will be stuck on rinse. 

Wear and tear, mineral buildup, and electrical failures are what causes the water inlet valve failure. Unexpected mineral buildup can clog the inlet valve, which is an obstacle to the proper water flow. 

Besides, electrical defects or wear and tear can result in malfunctioning the valve. In order to check the condition, simply get the power supply of the washer disconnected and locate the valve on the rear of the machine. 

Then, shut down the water supply system to see the condition of the valve. Clogged or debris buildup can be eliminated by cleaning. But in case you notice infinite reading by testing the resistance, go for a water inlet valve replacement!

Hopefully, the given video will be helpful for you in case of DIY valve replacement: 

4. Defective Washer Timer (Test/Replace the Timer)

Whether your Whirlpool washer is semi-automatic or automatic, the functionality really depends on its timer. In fact, it is highly liable to control the 3 cycles (e.g. rinse, wash, & spin). So if the timer fails to send signals to the machine due to any defects, the washer will be stuck during a rinse!

It is wise to check the condition of the timer through a multimeter. In this case, get your hands on the owner’s manual in terms of locating it. Possibly, you can find it on the washer’s top or control panel’s rear spot.

After testing it for continuity, if you find significant faults on the timer, go for the straight replacement without thinking twice. Consult someone expert if you are not sure whether it is fixable or not. 

5. Malfunctioned Lid Switch (Contact a Technician)

The safety system of the Whirlpool washer keeps on running once you close the door correctly. Afterward, the lid switch plays a crucial role in sending a signal to the control board.

As a result, your washer may start performing unusually or even get stuck on rinse when there is any issue with the switch!

We’d prefer to contact the Whirlpool Service Center to fix the defective lid switch, especially if your washer has a warranty. It is still better to consult an expert for further testing and replacing the lid switch.

6. Loose/Damaged Drain Hose (Tighten/Replace the Hose)

From the hose, the used water passes out of the washer once you wash your clothes. So, in case it gets clogged, the water will fail to escape and eventually result in being stuck on rinse. And the same issue will continue if the hose becomes loose or totally damaged!

After disconnecting the Whirlpool washer, get into accessing the drain hose to find the actual problem. Tighten it if you find it loose. But if it is drastically clogged or damaged, replace the hose with experts’ assistance.

FAQs

Ending up with a stuck Whirlpool washer during a rinse is a huge bummer for newbie users. So, in case you have more queries regarding it, keep on going through the following question-answers –

Final Words!

Getting the washer stuck is always a matter of concern! So, when we specifically talk about the Whirlpool washer stuck on rinse, it is necessary to pay attention to the timer and water inlet valve first.

Nonetheless, it is equally true that technical glitch is a common scenario, so you better start troubleshooting by resetting the machine. If it does not work, try out the other processes.