Whirlpool Washer Lid Lock Flashing [7 Troubleshooting Hacks]

After waiting a few minutes, you open the washer’s door and notice the lid gets locked! In that situation, the lid lock light may have started flashing constantly, which warns you that something is not going well!

Potential causes of the Whirlpool washer lid lock flashing include the faulty actuator motor, lid switch defects, damaged water inlet valve, and clogged drain pump. Striker misalignment, unintentional child lock activation, and a faulty control board can also cause the same problem.

Without knowing the details, you cannot know how to deal with each problem. So let’s dive in for further information!

Troubleshooting and Fix for Whirlpool Washer Lid Lock Flashing

As there are many reasons why the Whirlpool washer lid lock starts flashing, the troubleshooting processes will be several as well.

For instance, some steps might be performed through slight repairing, while others may need a straight replacement to troubleshoot the potential issue. Let us cut to the chase by discussing the methods:

1. Loose/Faulty Actuator Motor (Tighten the Wiring/Replace the Actuator Motor)

Here is where you should pay attention first. Because you can find its wiring either loose or totally faulty, which causes your Whirlpool washer lid lock to flash unexpectedly! And depending on the issue, you need to take the next step to overcome the problem.

But to be sure whether the actuator motor has turned faulty or there is only loose wiring, you must reach the machine.

Before touching it with your bare hands, make sure to disconnect the power for safety, and never touch it without unplugging it as well.

Let’s tighten the loose connections if required. Rapid spinning is often responsible for the loose connectivity.

However, if it is still not working, then you might have to replace it to overcome the lid lock flashing issue.

2. Lid Switch Defects (Change or Fix the Lid Switch)

Chances are the door lock will not work, and this mostly happens because of the defective lid switch. Either electrical or mechanical failure is liable for the issue with the washer lid switch.

For instance, electrical failure refers to the issues with the connection and wiring to the lid switch. In contrast, mechanical failure refers to physical damage to the lid switch.

But no matter what, both will eventually cause lid lock flashing. As a result, you must go for a straight replacement in case it is a mechanical failure.

On the other hand, you are lucky enough if the problem is related to electricity. Because to fix it, all you need is to re-check the connections and wiring.

3. Misaligned Striker (Re-align the Striker Properly)

The striker is considered a vital part of the washer. Basically, it assists in pressing the lid switch down. Over the period, there is a chance that the striker has moved from its actual spot.

Or let’s say it can also become slightly loose over time due to constant vibration.

And that is when the issue with lid lock flashing occurs on Whirlpool washer! In most cases, realigning the striker can solve the matter within no time.

To do so, simply use your fingers to apply slight force in order to put the striker back in its exact place.

4. Accidental Child Lock Turn-on (Power Off the Child Lock)

Child lock, also known as control lock, is a safety feature that is often used during the wash cycle.

There is a chance that the lid lock light of your Whirlpool washer will keep on flashing if you have activated this feature.

So, switching it off might be the only way to get rid of that situation. In this case, get into locating the button to deactivate/turn off the control lock.

Afterward, you can notice that the lid lock is not flashing if that was happening for the control lock feature activation.

Feel free to check out the product help. Whirlpool to get a detailed view of the control lock’s activation, deactivation, and so on!

Alternatively, you can watch the given video for a practical view:

5. Faulty Water Inlet Valve (Check/Replace the Water Inlet Valve)

Possibly, the water supply system of your Whirlpool washer is switched off, which is why the lid lock is flashing. To turn the water valves on, get behind the Whirlpool washer right away.

But if you notice the lid lock is still flashing despite being on, then chances are the water inlet valve has turned faulty.

And note that the functionality of this component is to maintain the water flow, which can be found on the rear of the washer.

So, if you find the water inlet valve completely defective, replace it immediately.

6. Control Board Malfunction (Check/Replace the Control Board)

Are you still noticing issues with the washer lid lock flashing? If so, then it is time to focus on the control board. It is mainly responsible for maintaining the communications between the washer and other crucial components.

Unfortunately, the control board may start malfunctioning due to excess/less voltage, inappropriate wiring, or control board overheating!

If the problem has been occurring for the inappropriate voltage, consider maintaining the voltage level by consulting a technician. Besides, if that was happening for the overheating issue, give your washer a rest to get it normal.

In contrast, you must replace the control board in case it becomes faulty. This must be done by qualified technicians.

7. Clogged Drain Pump (Unclog or Replace the Drain Pump)

If none of the above methods work to troubleshoot the Whirlpool washer flashing lid lock issue, pay attention to the drain pump. Basically, it assists in expelling water from your Whirlpool washer at the time of draining cycle.

So, in case it stops working, the water will remain backed up inside the washing machine, resulting in keeping the lid lock flashing! In this case, replacing the drain pump is the only solution that should be done by experts.

On the other hand, if it has become clogged after years of constant use, unclog the drain pump immediately. For that, we find it safe to take plumbers’ support.

FAQs

There might be some other uncommon reasons causing the Whirlpool washer lid lock to flash. Get to see them through the queries, including quick solutions, and so forth:

Final Words

We’d say “Whirlpool washer lid lock flashing” is more like a technical issue. So, do not dare touch any internal components without proper safety and technical knowledge. And in terms of repairing or replacing, it is wise to consult experts.

On the other hand, if the connection of wirings is loose, feel free to tighten them after shutting off the washer’s power.