Why Is Maytag Centennial Washer Lid Lock Flashing? Troubleshooting & Fixes

Maytag Centennial washer is loved among the users because of its reliability and performance. However, some users have reported that the lid lock of the washer starts flashing randomly. This problem interferes with the wash cycle as it’s unknown whether the lid has been locked or not.

Maytag Centennial washer lid lock flashing happens due to something getting in the way of the lid striker or the misalignment of the lid lock switch. Faulty lid lock switch and actuator motor is also the cause of this. Apart from these, loose wire harnesses, longer drum fill time leads to the lid lock flashing.

Let’s dive down deep into the reasons behind this lid lock flashing randomly. We have also included the fixes for each problem in this guide for your convenience.

What Causes of Maytag Centennial Washer Lid Lock Flashing?

As with any other washers, the Maytag Centennial washer lid needs to be completely locked before the wash cycle. Without the lid lock sign turning on, the washer door will act up.

If you wanna find out the source of this problem, there could be a few possible explanations for this.

• Lock striker is out of alignment with the lid lock switch
• Something is in the way of the lid lock switch and lock striker
• Built up lint and detergent on the edges of the lid
• Lid lock not working
• Longer fill time due to drain or inlet hose blockage
• Faulty actuator motor

Troubleshooting and Fix For Lid Lock Flashing on Maytag Centennial Washer

In order to figure out exactly which part of the washer is causing the problem, you need to inspect different components of the washer. Only then you can figure out what to do to fix the issue.

Make sure to turn off and unplug the washer before conducting any of the inspections. Then, follow through these troubleshooting instructions and fix the lid lock flashing problem.

Video Guide:

1. Look For Lid Interference

The most common reason behind a flashing lid lock is interference with the lock switch. There is a lock striker at the edge of the lid of the washer. This lock striker presses down on the lid lock switch in order to turn it on.

If there is any kind of interference with the lock striker, it can’t properly press down the lock switch.

As a result, the lid can’t be closed all the way. Lint and detergent building up around the edge of the lid is the main obstruction for the lid striker.

To fix this issue, cleaning is the best solution. Use a mild soap on a sponge or cloth and wipe down any stuck lint or detergent around the edge of the lid. Clear any other blockages along the lid edge for the lid striker to function fully.

2. Ensure Lid Lock Switch And Lid Striker Are Properly Aligned

Maytag Centennial washer lid lock flashing also occurs when two certain components don’t touch each other. The lid lock switch and lid striker need to be properly aligned or else the lid lock will keep flashing.

Due to slamming the washer lid shut over the course of time, the components might get out of place. The vibrations from the wash cycle can also misalign them accidentally.

Unplug the washer and remove the lid of the washer first. Align the lid lock switch and lid striker in such a way so that they are in contact with one another. You can use the instruction manual to ensure their correct positions.

3. Secure The Wire Harness To The Main Control

The wires in the internal connection system could be at fault for the flashing lid lock lights. The wires could be damaged over time or just come loose from all the vibrations.

In such circumstances, connection to the main control board is disrupted and the lid lock light flashes uncontrollably.

Take off the lid of the washer and locate the wires connecting inside. Make sure none of the wires are loose or disconnected from the main control board. You can seek help from a professional for this inspection.

4. Notice If The Fill Time Is Too Long

If the Maytag Centennial washer takes too long to fill the drum, it sets off some lights including the lid lock light flash. Water going in the drum or going out- any of the two could be the reason for the lid lock flashing.

Issues with water draining or filling usually happens because of problems with the inlet hoses. This eventually leads to wash cycle and door lock failure. And so, the lid lock light starts flashing.

Unplug the water and remove the drain and inlet hoses from the washer to fix this. Clear either hoses from any kinds of blockages or debris. Reattach the hoses to the washer. Ensure that the hoses are installed correctly as stated in the manufacturer’s manual.

5. Check The Lid Lock Switch Functionality

Another most likely source of the lid lock flashing can be a faulty lid switch. If the switch simply ran out of its lifespan, it won’t function anymore. Meaning, the lid lock can’t detect whether or not the lid is closed. Instead, it keeps flashing all the time.

The only way to fix a damaged or broken lid switch is to replace it. You can do it yourself if you have the proper tools and skills. However, it can be pretty complicated. So, contact an expert to replace the lid switch of the washer.

6. Find Out If The Actual Motor Is Working

Actuator motor on a Maytag washer is actually in charge of spinning the drum inside during the wash cycle. However, a faulty or malfunctioning actuator motor can prevent the lid lock switch from functioning as well.

If you don’t find anything suspicious after checking the other mentioned components, it’s very likely that the actuator motor is the problem.

To fix the actuator, it is best to call for a professional repairer. If the actuator motor simply needs tightening some connections, it can be done quickly. However, if it is way too damaged to function, you’ll need to replace it with the help of the expert.

FAQs

You’ll find out some of the questions and their answers regarding the Maytag Centennial washer lid lock flashing problem in this section.

Conclusion

No matter how reliable your Maytag Centennial washer is, it is very prone to simple problems like this.

Maytag centennial washer lid lock flashing can be fixed in no time with simple DIY and tool knowledge at home.

Only if you are aware of the problematic components and required skills, can you fix it within the shortest time.

The lid lock flashing also is a side effect of some other error codes. So, being aware of the washer error codes is also a good move.