Whirlpool Washer Shaking Violently on Spin Cycle: Quick Fixes!

After completing the wash cycle, you get into extracting moisture from your clothes through a spin cycle and notice the washer tub is shaking! And this goes really worse when you observe violent shaking.

Overloading, imbalanced washer, damaged suspension rods, and faulty drum bearing can cause issues with the Whirlpool washer shaking violently on spin cycle. The washer can also start shaking aggressively in case you forget to remove shipping bolts after the purchase.

As there are some technical problems involved, you cannot deal with each without proper education. So, let us disclose the troubleshooting details.

Troubleshooting and Fix for Whirlpool Washer Shaking Violently on Spin Cycle Issue 

Indeed, if your Whirlpool washer shakes a little bit, it is totally acceptable and normal. In fact, not only the Whirlpool washer, but almost every washing machine is also prone to vibrate during a spin cycle!

But the matter of concern is when your Whirlpool washer starts shaking violently during the spin cycle. It is definitely a major problem, which you should fix before the next use.

So, without further chit-chat, let us shortly discuss the causes of the violent shaking with quick troubleshooting ideas –

1. Excessive Load (Reduce the Load)

If your Whirlpool washer has loaded plenty of clothes that make it overloaded, it is pretty common to end up violently shaking on spin cycle.

In fact, it is the main culprit that most of you often ignore with the tendency that you will clean up all dirty clothes at once!

But guess what? Not only does it cause shaking violently, but this can also bring unexpected pressure on the washer, which is not good.

So consider reducing some extra clothes by opening the lid. Then, you can start the Whirlpool washer again to see how it is working now.

The best way to maintain its capacity is to read the owner’s manual, where you can get an idea of the total capacity of your washer.

It is wise to put slightly fewer clothes from the maximum capacity for the best results. Note that top-loading and front-loading models serve different capacities.

2. Imbalanced Washer (Balancing the Washer)

In case most of the loads are on one corner of your Whirlpool washer, it causes an imbalance while performing a spin cycle. And that is when the washer starts shaking aggressively!

So even distribution is the key to getting rid of the issue with imbalanced washers. Make sure the interior load of the washer is balanced.

Whirlpool.com suggests putting a few extra clothes for an even distribution. In fact, it is the simplest way to equalize the internal weight.

But if your Whirlpool washer is still vibrating or shaking violently, get into adjusting the washer’s leveling legs. Pay attention to each leg to confirm they are in contact with the bottom evenly.

3. Faulty Suspension Rods (Replace Them)

The key functionality of suspension rods is to dampen the washer tub’s movement. So it is not a secret that your Whirlpool washer will start

shaking violently on the spin cycle when any of the rods become damaged!

After disconnecting the power, you must inspect it carefully by opening the front panel of the Whirlpool washer. Over time, they tend to wear out and eventually become useless.

So except if there is any problem with tightening or loosening connections, do not think twice to replace the rods right away. Because in most cases, a worn-out suspension rod is not something that you can repair.

We guess the following video will be helpful for you in terms of the suspension kit replacement:

4. Forget to Take Off Shipping Bolts (Remove Them)

Almost every front-load washer will be shipped with some specific bolts mainly for stabilizing the drum while transporting.

But these are not something you should keep as it is! Because shipping bolts can cause a violent shaking, and even some permanent damages as well.

So during the installation, be sure to take them off right away using a screwdriver. This will be located on the rear of your Whirlpool washer.

5. Snubber Pad Worn-out (Replace the Snubber Pad)

In simple words, a snubber pad assists in decreasing the vibrations and noises during a spin cycle.

So, in case it is missing, worn out, or comes into direct contact with sticky substances, your Whirlpool washer will start shaking violently!

As a result, you must replace it immediately to overcome the bad consequences. For the inspection, get your washer unplugged, and take the access panel off to locate the pad.

Pay attention to that for identifying any potential signs regarding damage or wear.

6. Damaged Drum Bearing (Replace It)

In order to confirm a smooth and steady spinning cycle, the Whirlpool washer’s drum needs a specific bearing.

But over the period, it is also prone to lose its efficacy and become faulty, just like other crucial components.

And this often happens with the Whirlpool washers because they are prone to create excessive pressure to clean up the clothes.

Gradually, the drum bearing gets damaged and results in the Whirlpool washer shaking violently on spin cycle!

Note that sealing the bearing is not enough to overcome the issue. In that case, you must go for the replacement.

Based on HomeAdvisor’s report, this will cost around 150-230 dollars, which includes the labor charge as well.

7. Interior Failure (Contact A Technician)

Even after trying all the nooks and crannies above, are you still noticing the issue with the Whirlpool washer shaking violently on the spin cycle?

Well, this can happen due to internal failure of the components, which you cannot fix by yourself.

In such a case, it is safe to consult your nearest technician for help. You can also contact Whirlpool’s support center, whether your washer still has a warranty or not.

FAQs

Being a new user of the Whirlpool washer, it is common to have more queries related to it. Let us discuss more about its potential failures and the quickest way to solve them:

Final Words!

Even though the issues with the Whirlpool washer shaking violently on spin cycle are many, you should not get worried.

Because, in most cases, overloaded clothes and imbalanced loads often cause violent shaking, which is easily fixable by yourself.

But we’d prefer monitoring the washer on a daily basis to inspect the potential technical issue. If you find anything major, consult experts right away.