Maytag Washer No Power: Reasons + How To Fix It!
Maytag washer is widely considered the most dependable and powerful home appliance. But there are times when these complex machines do not work as you intend. Although that’s graspable for the Maytag washer, no power either!
A number of reasons are responsible for the problem. The problem can be as simple as a minor issue in the incoming power supply, faulty wire, enabled control lock, or corroded contact points. In the worst case, it can be due to a damaged main board.
Don’t panic. There are many more solutions that can solve the problem before finalizing the broken mainboard as the reason. So, without any ado, let’s get into the details.
Troubleshooting and Fixing For Maytag Washer That Is Not Powering On
Nothing can be more frustrating than when you are about to do your laundry and see that out of nowhere the washer is not powering on. As you already got the hint about what things can be wrong with the washer, let’s get the problem solved starting from the simplest to the hardest.
1. Check The Incoming Power Supply
If your Maytag washer is not getting power on, the possibility can be that the washer is not getting enough power due to a broken power cord, tripped circuit breaker, or blown-out fuse.
So, whenever you face a problem in your washer don’t jump to the conclusion of predicting something big. First, check whether your washer is getting a proper power supply. Let’s see how.
- Reset The Maytag Washer
You can first try to reset the Maytag washer by unplugging the washer from its power source. Wait for at least one minute. After that plug back in and see whether the power is restored.
- Check The Power Cord
Now check whether the power cord of the washer is completely plugged in or has any signs of defect or damage. Repair or replace if you notice one.
- Check The Circuit Breaker
Inspect the circuit breaker of your home and reset the tripped ones.
- Replace Blown Fuse
If the case is a blown fuse, it’s obvious that the washer won’t power on. Once this sacrificial device is blown out, you must replace it.
2. Disable The Control Lock
If there is nothing wrong with the incoming power supply or its source, it can happen that you have mistakenly enabled the Control Lock of your Maytag washer.
When the Control Lock is activated, you will see the Control Lock light on. Due to this, controls don’t respond to any touch attempts.
You can disable the activated control lock feature on your top load and front load Maytag washer just by holding the Control Lock button for about 3 seconds.
It’s that easy!
3. Check Lid And Replace The Lid Switch
The Maytag washer will only start when the lid is properly closed and the lid switch is engaged.
That’s why, first, ensure the door is properly closed. If there is any debris or obstructions interfering with the proper closure of the lid of the washer, clean it with water, cleaning soap, and a soft cloth.
If the lid is all right, move ahead to check the lid switch. You should check the lid switch with the multimeter and if there is a lack of continuity, the switch must be replaced. For replacement, it is always recommended to take the technician’s help.
However, you can refer to the below YouTube video for a complete video tutorial for replacing the lid switch of the Maytag washer.
4. Clean The Corroded Contact Points
When the washer is not working, the other reason is the corroded contact pads on the contact points. The user interface or the control panel is the section that you use to interact with the washer.
It sends the signals to the main control board through the wire harness. Steams from the washer cause the control panel to be corroded over time. When that happens it causes problems making the washer not work.
To solve the problem, you need to clean the corroded contact point. The steps are below.
- Separate the user interface by disconnecting the wire harness.
- Now use rubbing alcohol on a wiper and clean all the corroded points of the control panel gently.
- Wait for one or two minutes letting the control panel dry. After that place the control panel in its place.
5. Check The Wiring Between The User Interface And the Main Control Board
Apart from the corroded user interface, problems with the wire harness are another obvious reason for the washer not working out.
The wire harness is crucial as it connects the control panel and the main control board directly and sends signals. So, now inspect the wiring whether it is faulty.
- Take the help of the user manual to get access to the wire.
- If you find any damage, replace the wire.
6. Replace The User Interface
You know, your Maytag washer will not start working until you press the start button of the washer control panel for 3 seconds. Sometimes it happens that everything is alright but the Start button has gone bad itself.
If you see that some of the buttons of the control panel are illuminating or the control panel is totally dark whereas the power supply is ok, it is more likely that the control panel is faulty. Replace the control panel now.
7. Replace The Damaged Main Control Board
If you have tried out all the possible fixes for a Maytag washer no power, but found no luck, the very last reason can be a damaged main control board.
Excessive wear and tear caused by long usage is one of the main reasons for the damaged main control board. To solve the problem, you need to replace it.
Here are the key points for replacing the main control board.
- Step 1– Locate the board assembly.
- Step 2– Remove the wire cover and disconnect all the wire connectors connected to the board.
- Step 3– Detach the damaged board and install the new one.
- Step 4– Now reattach all the wire connectors that you have detached before and close the cover securing the screws.
To do this job it is better to take the expert’s assistance. But if you are tech-savvy and want to do the job by yourself with some assistance, the below video will be a great help for you.
Note: The main control board is a rare failure, better to check all the commonly defected parts before replacing the board.
FAQs
Although we have a detailed discussion about the Maytag washer not powering up the problem, here are some queries that are mostly searched for.
Why is my Maytag washer clicking but not starting?
If your Maytag washer is making a clicking noise but not starting it is mostly due to the faulty door lock motor and switch assembly. However, faulty lid switch assembly can also cause the Maytag washer just to make a noise instead of starting up.
Why is my Maytag washer making the error ‘Beeps’?
Typically, the Maytag washer does not start and makes beep sounds when the door has not been opened or closed for 3 cycles at least. You just need to open and close the door of your washer to clear the error from the display.
Why is my Maytag washer turning on but not starting?
If your Maytag washer is turning on but not starting, it can be due to a fault setting. When the Delayed Start setting is enabled, you may face the problem of delaying the start of the washing cycle.
Why won’t my Maytag washer spin or agitate?
When the tub of your Maytag washer is not spinning or agitating, it can be due to the broken shift actuator. Moreover, a faulty washer transmission can also be responsible for the issue.
Final Words
Well, that’s all from us today! Expectedly, you have pointed out what’s going wrong behind the Maytag washer no power issue. However, let’s recap!
Whenever the washer is not turning on, your first attempt should check the power supply and control lock.
It doesn’t work, check the other component that we mentioned. If you need any further help, ring up a call to the Maytag Customer Center.