Fix GE Washer Spin Light Blinking: Quick Guide

Imagine you switched on your GE washer to clean up a pile of dirty clothes. And all of a sudden, you notice the spin light starts blinking! This can give you a panic attack, especially if you cannot detect why it is happening.

Issues with the GE washer spin light blinking occur mainly for the imbalanced load. A defective lid switch, faulty mixing valve, or damaged belt can also be the culprit behind the problem. It is equally important to check the capacitor’s wire as the spin light may blink due to broken wires.

Still confused? Well, stick here from head to toe for the details!

What Does the Spin Light Blinking Mean?

In simple words, the spin light has a connection to the washer’s water level, as it turns on if the level of water changes. So you can see it has a straight connection with the fluctuation of the water level. And it tends to start blinking when the washer detects an imbalanced condition. 

In most cases, spin link blinking does not often stay illuminated for a long period, especially after the completion of the water cycle. Sometimes, the light spins at a maximum speed when the GE washer fails to maintain the required load.

Why GE Washer Spin Light Blinking?

There might be something that is not allowing the washer to act in the way it should be! It happens for numerous reasons, so there is no way to blame a single component of the GE Washer when the spin light blinks!

Even though the imbalanced load or condition is considered the core reason behind the GE washer spin light blinking, the following reasons can also cause the issue:

• Faulty lid switch 
• Damaged mixing valve
• Broken Wire  
• Inappropriately-adjusted rubber cords
• Defective belt

There can be some other uncommon reasons causing the GE washer spin light to blink unwantedly. But the above ones are known to be quite common and are often faced and complained by GE washer users.

Troubleshooting GE Washer Spin Light Blinking Issue

The troubleshooting process of the spin light blinking issue is not going to be easy! Because depending on where the fault is, you will have to apply a particular technique to get rid of the bummer.

Besides, if you do not have basic technical knowledge, then you may not fix them unless you get assistance from an expert technician.

However, for your convenience and better understanding, we’d try to teach you in the most basic way possible:

1. Replace the Lid Switch

The majority of washer lid switches are made of plastic, and so with the GE washer! So after years of constant use or improper dealing, it is common for the switch to get broken or damaged.

So in such a case, there is nothing to do, except for replacing it right away to fix the spin light blinking issue. RepairClinic recommends using a multimeter to check the condition of the lid switch before the replacement.

2. Mixing Valve Replacement

Mixing up the cold and hot water is the general function of the washer’s mixing valve. So prior to reaching the max, the mixing valve plays a key role in preventing scalding by combining proper water levels.

So if you do not attempt to replace it when needed, then the GE washer spin light will continue blinking unwantedly. Fortunately, the mixing valve replacement will not cost you a fortune, as it charges below 50 dollars only!

3. Repair or Change the Broken Wire

You cannot expect your GE washer to run if there is something wrong with the capacitor.

And if the capacitor’s wiring has any complications, or let’s say gets damaged, then you can face problems with the spin light blinking on the GE washer!

The washer unit will be located around the bottom side with two wirings (blue and red). Carefully pull any of them to confirm whether the wires are loose or broken.

As you are using your bare hands, it is a “MUST” to break the power connection. Moreover, you need to make sure the capacitor holds energy for a short time. 

N.B: Do not take any risk if you have not dealt with wiring before. Because it may cause mild to severe damages or injuries with inappropriate operation. So consult an electrician/mechanic if required.

4. Adjust the Rubber Cords

At the tub’s top, you can locate four rubber cords. Chances are they might be moved from their actual spot during the washer movement, especially when you shift it from one place to another. 

In this case, simply adjust the cords to get them well-settled into their actual place using your hands.

You may also need to tighten the cords a little bit to see whether it has fixed the light-blinking issue or not.

5. Change/Replace the Belt

During the water cycle, the belt assists in turning the drum of the water. So there is a slight chance that the belt will slip accidentally if any cloth gets stuck between the outer and inner tub’.

In case that causes the belt to get broken or burn, the spin light may start blinking!

The only solution here is to replace the belt as soon as possible to solve the issue. According to Homeguide, the total cost of belt replacement is around 100-200 dollars, depending on the washer’s model.

But do you only want to spend on the washer belt? If so, then it will cost you only around 5-30 dollars. Do not hesitate to change it yourself at home through the video tutorial:

FAQ’s:

Do you want to learn more about the spin light blinking or related to it? Go through the following frequently asked questions and see what matches your queries:

Final Words 

There is no need to get straight into the repair shop if your GE washer spin light blinking. Rather, pay attention to the interior condition of the washer first to confirm whether it is overloaded or not.

If not, then start observing the lid switch, mixing valve, and belt gradually. Read the owner’s manual to earn detailed knowledge of each component of the washer.