Kenmore Dishwasher Filter Removal – A step-By-Step Guide

If you have been using your Kenmore dishwasher for a while, the most likely reason the washer is not cleaning effectively is a clogged filter. If so, you need to clean it. Fortunately, locating, removing, and cleaning is not a tough job to do.

First, unplug the dishwasher. Now, locate the filter; in almost all models, it can be found near the bottom. After that, you have to pull the lower rack out. Finally, grab the spray arm and pull it up with a tug. Just under the spray arm, you will find the filter attached to the arm. Now what you have to do is self explanatory.

That’s all. Anyway,  we will have a detailed discussion below and some other relevant points that you might want to know!

Tools Needed For Removing Kenmore Dishwasher Filter

As stated, no special tool is needed to remove the filter; however, some washers require you to remove screws, which means you need a screwdriver to remove the screws and access the filter.

 In addition, for safety purposes, you may need the following gadget:

• Gloves, 
• Safety glasses
• Towel or cleaning brush

Finally, if the purpose of the removal is to replace it, then you need a replacement filter.

How to Remove Kenmore Filter?

Unlike any other mechanical instrument, for example, your car has a filter too, but that is not easy to locate and remove. You might need previous experience, skills, and tools to carry out the job.

However, in the case of a dishwasher, one can easily find and remove the filter without much effort. Also, you do not require any special tools.

Step 1: Unplug the Dishwasher

The very first step is to unplug the dishwasher. This is probably for safety purposes, but do it first rather than in the middle of the job.

Step 2: Remove Everything

Now the next obvious step is to remove all the dishes, utensils, and other instruments from the washer.

Step 3: Locate the Filter

So the necessary preparation before removing the filter is done. Now, you have to locate the filter position, which is at the bottom. But you can’t fully access the filter until you remove the bottom dish rack. Now simply pull the locker rack out.

Step 4: Identify the Filter and Remove it

After removing the lower rack, you will see the spray arm. Grasp the spray arm; you may have to rotate it right and lift it out.

Just below the spray arm is the filter. It can be removed by turning it counterclockwise and lifting it out.

There can be different types of filters.  Depending on the model, some Kenmore filter assemblies are attached with screws; in that case, remove the screws first.

Step 5: Clean the Filter

Once the filter is successfully lifted out, remove any debris or food particles. If there is a tough spot, use a soft-bristled cleaning brush to gently brush the filter clean. Also, you can rinse the filter under running water to remove bad particles.

Step 6: Reinstall the Filter

So you’re done with the cleaning. Once the filter is clean, put it back in place. Make sure it is properly seated and secured. Replace the bottom dish rack and close the dishwasher door.

Step 7: Run the Dishwasher

Once everything is put back in place, test run the dishwasher. It should be working more effectively than before. When testing the Kenmore dishwasher, just to be sure it is empty with no dish inside, That’s all.

How To Tell When To Replace A kenmore Dishwasher Filter

Kenmore is a renowned company for kitchen appliances, so they make sure their kitchenware is unique and durable. In general, you can expect your dishwasher to last for at least 10 years. With maintenance, it should go beyond that.

However, over time, the Kenmore dishwasher accumulates food remains and other small particles, which make the filter vulnerable. That’s ok. You need to make sure the filter is free of blockage by removing these bad elements periodically.

But Sometimes, due to your busy schedule, you may fail to carry out proper inspection periodically, so filter assemblies may develop cracks, holes, or other signs of wear and tear. In that case, you might have to replace the filter.

If not every week, do an inspection per month, remove everything, and check the filter for clogs. If it is worn or some parts are broken, replace it or simply clean the filter.

The most obvious sign of an ineffective dishwasher is that it takes longer to complete a cycle. If so, you must carry out the inspection.

Finally, if you notice a foul or unpleasant odor or the water is not draining properly, you must check the health of the Kenmore dishwasher filter and replace it if necessary.

The general rule to keep the filter operating for longer is to inspect it closely after a few months and keep doing so.

FAQ

We have tried to provide all the necessary information, and hopefully you have successfully removed and cleaned the Kenmore dishwasher filter. Still, you may have some questions. Here are some frequently asked questions that you might want to know.

Final Words

So there you have it.  You probably have your answer. If this is your first time removing the filter and cleaning it, it is a good idea to watch a video tutorial or talk to an expert.

One last piece of advice: keep it properly maintained and clean the interior of the dishwasher by using a dishwasher cleaner. Hopefully, the Kenmore dishwasher will stay with you for a long time.